SureFit® Performance Guide
The SureFit hosel features a sleeve and ring, each with four settings. The sleeve settings are numbered 1, 2, 3, 4, and the ring settings are lettered A, B, C, D. There are 16 unique loft and lie angle combinations.
Insert SureFit wrench into hosel screw and rotate counter-clockwise until hosel becomes loose, move adjustment ring to desired setting, and tighten clockwise until you feel and hear the wrench “click”. If the screw feels like it is binding, stop and realign components.
- 917, 915, 913 and 910 driver shafts are interchangeable.
- 917, 915 and 913 fairway shafts are interchangeable.
- 816, 915 and 913 hybrid shafts are interchangeable.
- 915, 913 hosel adjusts in 0.75° loft and lie increments if used in 816 heads.
- 816 hosel adjusts in 1.0° loft & lie increments if used in 915 and 913 heads.
SureFit Hosel Performance Fitting Guides
Start in the standard position: A•1 (RH) or D•4 (LH).
Move up or down in the grid to adjust trajectory.
Move left or right in the grid to fine tune direction.
+/- .75° denotes driver settings; +/- 1° denotes hybrid setting.
*LOFT = EFFECTIVE LOFT with a square face at impact.
For best results, see an authorized Titleist Fitter.
30 MINUTES. 30 SWINGS. 1 PERFECT DRIVER.
Maximize the performance of your new Titleist 917 driver with the help of a Titleist Certified Club Fitting. If you can give us approximately 30 minutes and 30 swings, we know you'll be blown away by the performance gains. Search below to find a club fitting location near you.
Insert tip of SureFit Wrench into SureFit CG Weight end cap to remove installed weight. Rotate wrench counterclockwise until end cap is loose and can be removed by hand. Carefully remove end cap from head and set it aside in a secure area. Remove weight from driver head.
IMPORTANT NOTE: End cap will be separate from weight. Make sure to hold the end cap securely.
Once the SureFit CG Weight and end cap have been placed into the desired setting, insert weight by hand into weight port. Insert SureFit wrench into weight end cap. Rotate wrench clockwise until you feel the wrench “click”.
SureFit CG Weight Settings
View + / • / - on tip end of weight. Arrows will help determine what side goes in first for desired result.
917 Metals are shipped with one additional SureFit CG Weight.
- If your 917 metal was shipped with the Neutral weight installed in the head, then you will have a loose Draw/Fade weight.
- If your 917 metal was shipped with the Draw/Fade weight installed in the head, then you will have a loose Neutral weight.
- Additional heavier and lighter weights sold separately. 917 driver and fairway weights are not interchangeable.
Experience Titleist Golf Clubs
The best way to truly appreciate the complete performance of Titleist golf clubs, achieve total confidence on every shot, and shoot lower scores, is to experience Titleist club fitting for yourself. Find a fitting location by using the search tool below or calling 1-888-TITLEIST.
Experience Titleist Golf Clubs
Read instructions completely before use.
The SureFit® wrench must be used to properly and safely adjust the performance of Titleist metals. Club components should be inspected frequently, before and during play, to ensure that all connections are tight. Keep the hosel connection area clean from dirt and debris at all times. This proprietary system is only compatible with genuine Titleist components and must NOT be used with components from other manufacturers. Failure to adhere to this provision may void the warranty and/or cause damage to the system. Failure to follow these instructions may create a situation where the clubhead could loosen or disengage from the shaft during a swing, possibly causing serious injury.
For more information, explore this website or U.S. consumers may also call Team Titleist at 1-888-TITLEIST. Titleist golf clubs conform to the Rules of Golf approved by the USGA and R&A. However, the settings on your golf club must not be adjusted during a round of golf. For complete rules information, visit www.usga.org or www.randa.org.